part-time4wd.com
  • Home
  • Blog
  • The Builds
  • tech
  • contact

oh noes

2/12/2019

 
Ok, update time.

Started on the doors:​
Picture
Picture
Picture
Picture
Door #2
Picture
Picture
​This is where my inexperience with sheetmetal repair shows. I took my time, but both doors sunk when i welded them. Cant have any filler since the mirror bolts up here, it would just crack. Its gotta be fixed, but im not sure how. Thus far ive only made it worse, which is disappointing.
Picture
​In my frustration, i decided to abandon the doors for now and start designing a rear bumper.
​Gutted the original tailgate, so i could easily install it.
Picture
​Back in place, with the green bronco's bumper still installed. I wanted the 'gate there for mockup of the rear bumper, and its nice & easy to move empty.
Picture
​Once i got some free time, i went over to the scrap steel yard and found some goodies:  3½x6 angle iron (oddball size but IMO perfect for a bumper). Also got some 2½x1/4" flat stock, and some cool lookin panels with speed holes in them:
Picture
Picture
​...and some 3/8" plate:
Picture
​I expect to use the angle & plate, i doubt i have a use for that stuff with the holes in it, but they had a ton of em and they looked cool so i bought two. I spent ~ $75 for all of it, so i figure im into the bumper for about $50 as of right now.

With the corners cut, the angle will fit up roughly here:
Picture
​Bumper brackets built out of the 3/8" plate:
Picture
​...and installed. My shackle hangars are forward on the frame to correct shackle angle, which gives me 5 existing holes in the frame to bolt to.
Picture
​...and the angle iron slotted to fit over the brackets
Picture
Picture
​The tabs sticking thru will get reinforced at a later date and become shackle mounts. This way theyll pull directly on the frame as opposed to just the face of the bumper.
Thats all i got; i have a rough idea for what i want the rear bumper to look like, but nothing is set in stone yet so im kind of designing it as i go. I know i want a centered lisc plate, a 2" receiver in the middle (either behind or below plate), i want to taper the corners, and i want to wrap around under the rear quarters to protect them. So ive got a bit of design work to do yet.


Comments are closed.

    Categories

    All
    203/205 Doubler
    3/4 Ton Conversion
    3g Alternator
    460
    5spd Swap
    88 Bronco
    90 Bronco
    96 Bronco
    96 F250
    Anti Wrap Bar
    AOAA
    Bed Liner
    Big Dogs Offroad
    Bilstein
    BW1356
    C6
    Dana 60
    Dump Bed
    E4OD
    East Coast Bronco Roundup
    ECBR
    Electric
    Electric Fan
    Fab Work
    Fender/carrier Repair
    Floor Vents
    Front Bumper
    Garage
    Gauges
    Half Cab Conversion
    Home Depot Bed
    Junkyard
    Junkyard Gems
    Kid Trax Bronco
    Leaf Sas
    Massey 3165
    Off Road
    On Board Air
    Pickup Cab Swap
    Pmgr Starter
    Rausch Creek
    Rear Bumper
    Recovery
    Rock Light
    Saginaw Swap
    SD Spring Swap
    Shackle Reversal
    Sliders
    Sliding Windows
    Solid Axle Swap
    Steering Column
    Sterling 10.25
    Tire Carrier Repair
    TTB TRE Flip
    Video
    Water Injection
    ZF S5-42

    Archives

    February 2025
    January 2025
    December 2024
    November 2024
    September 2024
    August 2024
    July 2024
    June 2024
    May 2024
    April 2024
    March 2024
    February 2024
    January 2024
    December 2023
    November 2023
    September 2023
    August 2023
    July 2023
    June 2023
    May 2023
    April 2023
    March 2023
    February 2023
    January 2023
    December 2022
    November 2022
    October 2022
    September 2022
    August 2022
    July 2022
    June 2022
    May 2022
    April 2022
    March 2022
    February 2022
    January 2022
    December 2021
    November 2021
    October 2021
    September 2021
    August 2021
    July 2021
    June 2021
    May 2021
    April 2021
    March 2021
    February 2021
    January 2021
    December 2020
    November 2020
    October 2020
    September 2020
    August 2020
    July 2020
    June 2020
    April 2020
    March 2020
    February 2020
    November 2019
    October 2019
    September 2019
    August 2019
    June 2019
    May 2019
    April 2019
    March 2019
    February 2019
    January 2019
    December 2018
    October 2018
    August 2018
    July 2018
    June 2018
    May 2018
    April 2018
    March 2018
    February 2018
    December 2017
    November 2017
    October 2017
    September 2017
    August 2017
    June 2017
    May 2017
    April 2017
    March 2017
    February 2017
    January 2017
    December 2016
    November 2016
    October 2016
    August 2016
    May 2016
    June 2015
    February 2015
    July 2014
    June 2014
    February 2014
    August 2013
    July 2013
    June 2013
    May 2013
    April 2013
    June 2012
    May 2012
    March 2012
    February 2012
    January 2012
    September 2009
    June 2009
    March 2009
    July 2008
    April 2008
    March 2008

  • Home
  • Blog
  • The Builds
  • tech
  • contact